Electric Solenoid Valve 1" Slip x Slip 24VAC

Note:  This valve has NO THREADS. It is a 1" slip x slip valve.

Product Description

Easy-to-use (and reach) manual bleed levers and flow control stems make adjusting water pressure simple. Industry standard threaded solenoids will work with most other irrigation products. Reverse flow diaphragm won't clog and operates well at as low as 10 PSI at only 1 GPH, to 150 PSI - perfect for drip irrigation systems all the way up to high volume needs. Compare our valves to the competition.

Product Details

Operating Range

• Pressure: 10 to 150 PSI
• DFV-075 Flow: 0.2 to 22 GPM
• DFV-100 Flow: 0.2 to 40 GPM
• DFV-100SS Flow: 0.2 to 40 GPM
• Water Temperature: Up to 110F (43 C)
• Ambient Air Temperature: Up to 125 F (52 C)

Electrical Specifications

• 24 VAC 50/60 cycle solenoid power requirement
• Inrush Current: 0.35 Amp (8.4 VA)
• Holding Current: 0.23 Amp (5.5 VA)
• Solenoid Coil Resistance: 24 Ohms

Dimensions

• Height: 4 3/8" (11.1 cm)
• Length: 5" (12.7 cm)
• Width: 3 1/16" (8.1 cm)

DFV Valve Technical Info Sheet (pdf)

Product Details

Operating Range

• Pressure: 10 to 150 PSI
• DFV-075 Flow: 0.2 to 22 GPM
• DFV-100 Flow: 0.2 to 40 GPM
• DFV-100SS Flow: 0.2 to 40 GPM
• Water Temperature: Up to 110F (43 C)
• Ambient Air Temperature: Up to 125 F (52 C)

Electrical Specifications

• 24 VAC 50/60 cycle solenoid power requirement
• Inrush Current: 0.35 Amp (8.4 VA)
• Holding Current: 0.23 Amp (5.5 VA)
• Solenoid Coil Resistance: 24 Ohms

Dimensions

• Height: 4 3/8" (11.1 cm)
• Length: 5" (12.7 cm)
• Width: 3 1/16" (8.1 cm)

DFV Valve Technical Info Sheet (pdf)

Replacement for

Irritrol 2500S 2500SF 205S 205SFRain Bird 100DFVSSToro TPV Series ValveWeathermatic Nitro Remote Control Valve N-100S-H N-100SF-HWeathermatic 12000 Series Valve

Related Tutorials

• Sprinkler System Basics
    Controllers, Valves, & Sprinklers

Tips & Tricks

Adjust Water Flow to Garden Boxes With a Flow Control Valve

1/2" Valve fits over mainline tubing

These valves are great when you have garden boxes or drip areas that you may want to turn off seasonally. You can reduce the flow or shut it off completely. 1/2" Flow  Control Valves are installed just like a compression coupler.

Install a rain or soil moisture sensor

Many irrigation controllers work with weather sensors

Rain and soil moisture sensors work like an on/off switch. They are easy to install and work with most irrigation controllers. Once installed, they will turn the system off until the rain stops and things dry out.

Watch for runoff

Check sidewalks and driveways

Be green and save money too. Check often for excessive runoff from your irrigation system as well as puddles or pools of water. It may only take a slight adjustment of nozzles, spray emitters, or water timers for substantial water savings.

Owners' Manuals & Troubleshooting Guides

• Irrigation Direct DFV Valve

Automatic Valve

A valve which can be remotely operated either electrically (the most common) or hydraulically. Automatic valves are commonly used as "control valves" for irrigation systems. See also Valve, Bleed Valve.

Controller

Also referred to as a clock, or timer, an irrigation controller is an electronic, programmable device that controls the timing of automatic electronic valves in an irrigation sytem. The valves control the flow of water to sprinklers and drip systems. The contoller sends electricty (low voltage) to the valve on the day and time set in the controller schedule and for the duration programmed by the user.

High end controllers employ weather-based controls ( ex. rain sensors, soil moisture monitors, real-time weather data), internet connections, cell phones, and remote controls for use with sophisticated irrigation systems. See also Irrigation Schedule.

Schedule 40

A PVC pipe classification (often written as SCH 40 or SCHED 40), commonly used for main line water pipes. Schedule 40 pipe is thicker than Class 200 and can withstand higher water pressure. The "schedule" number is not a specific measurement but rather a designation representing the reletive wall thickness of the pipe and water pressure rating (psi) for that pipe.  For additional classifications of irrigation pipe  see Shedule 80 and Class 200.

Valve Box

A rigid plastic container which covers and protects underground irrigation valves. It has an access lid for valve maintenance. See also Valve, Controller, Direct Bury Wire, Two Wire. 

Zone

Also called a watering zone, a "zone" is an individual watering area controlled by a single irrigation valve. It may be a group of sprinklers or a drip irrigation system. When designing an irrigation system, plan individual zones so that each contains plants with similar watering requirements. Watering zones should also consider micro climate factors like amount of sun exposure vs. shade, and design elements like sidewalks and driveways. With proper planning, you can create zones that allow flexible programming on your irrigation controller. See also Valve, Controller.

Diaphragm

The diaphragm is a flexible rubber membrane inside an automatic irrigation valve, between the upper chamber of the valve and the smaller valve inlet (water supply). When the valve is closed, both the upper chamber of the valve and the valve inlet are filled with water. Since the upper chamber is larger, a greater suface area of the diaphragm is covered with water than on the inlet side. This water pressure differential keeps the valve closed.

When the solenoid is electronically activated, it releases water from the upper chamber above the diaphragm. This reduces the water pressure above the diaphragm and allows it to rise and open the valve. Water will now flow through the valve.

A spring inside the valve pushes against the back of the diaphragm, but it does not exert much force on the diaphram. It would stay closed without the spring. See also Valve.

Pipe Thread

The common term for National Pipe Thread (NPT). Pipe threads require Teflon tape or pipe dope to create a water-tight seal. Do not thread together pipe threads and hose threads. See also Teflon Tape, Pipe Dope, Hose Thread.

Bleed Valve

Used to manually turn on an automatic valve. a bleed valve is located on or near the top of the valve. It can be a small screw, a lever, or built into the solenoid. When turned, the bleed valve allows water to flow out of the cavity over the internal diaphragm of the valve. This causes a pressure differential and opens the valve. 

If the bleed valve is an external type, a small stream of water will flow from the bleed valve and outside of the valve while it is on. An internal bleed will keep the water inside the valve and empty it into the downstream side of the valve. See also Valve.

Teflon Tape

A non-adhesive tape (made of Teflon non-stick material) that is used to create a water-tight seal with pipe threaded fittings. It is tightly wrapped in a clockwise motion 3-4 times around the male pipe threads. Male and female fittings are then threaded together.

View our complete glossary of irrigation terms.