Battery powered hose end irrigation timer with LCD display. Reliable & cost effective for home and garden drip irrigation systems.
Note: This timer is not designed for our Starter, Medium or Large size drip kits or where flow totals are under 75 gph. (1.25gpm) Use our Drip Pro Water Timer (DD-DWT673) instead. Not intended for use on gravity feed systems.
How to Install a Drip Irrigation Hose End Digital Timer
Irrigation Direct Product Tutorial
Hose End Digital Timer: DD-HEDT
The Hose End Digital Timer from Irrigation Direct is a battery operated unit that is used to automate the watering for a Drip Irrigation system. It connects to a standard hose bibb, faucet, spigot or any water source with ¾” MHT. It will also connect to a Y ball valve which gives you access for a garden hose.
The timer comes with 9 independent start times with watering run times from 1 to 255 minutes. It has a seven day programmable calendar and has a large digital display with 4 control buttons for easy programming.
The hose timer runs on 2 AA batteries and will last a full year on a fresh pair. To install the batteries, simply remove the battery cover on the rear of the unit with a small Philips screwdriver. Insert the batteries with the polarity as shown on the battery cover. When replacing the battery cover, it helps to hold the cover down while tightening the screws.
When the battery cover is attached, you may hear a pulsing sound coming from the unit for about 10 seconds. This is the timer’s startup mode and it insures that the internal ball valve is in the off position.
The Timer comes with a ¾” FHT inlet and a ¾” MHT outlet. It also has an adjustable lock nut that allows you to reposition the unit. Its maximum pressure input is 120 psi and its maximum flow output is 4 gallons per minute (= to 240 GPH).
As with all hose threads, no Teflon tape is required. A standard hose washer is used to make a water tight seal.
Installing a Hose end timer is quick and easy.
Simply screw the hose timer onto your desired water source. Hand tighten to make a water tight seal. To reposition, turn the lock ring to the left and turn the timer upright, then turn the lock ring to the right and lock into place.
For added protection against the elements, the timer comes with a protective cover which fits over the unit.
For programming, please refer to the included instruction sheet.
The HEDT Hose End Digital Timer is just one in a full line professional irrigation products available from Irrigation Direct.
- Excellent for Drip Irrigation
- Connects to 3/4" Hose Bibb or Y Ball Valve
- Digital Display
- Up to 9 Start Times Per Day
- Requires 2 - AA Batteries (not included)
- Water Budget Capability
- 1 to 255 Minute Run Time
- Rubber Boot Cover for Maximum Protection
- Inlet: 3/4" FHT (Female Hose Thread)
- Outlet: 3/4" MHT (Male Hose Thread)
- Maximum flow rate: 4 Gallons Per Minute
- Minimum inlet pressure: 10 psi
- Maximum inlet pressure: 120 psi
- Hose End Timer Instruction Sheet
Note: This timer is not designed for our Starter, Medium or Large size drip kits or where flow totals are under 75 gph (1.25gpm) Use our Drip Pro Water Timer (DD-DWT673) instead. Not intended for use on gravity feed systems.
DIG 9001DC 9001EZC Drip Depot 1005 DripKing 9001DC Dripworks TDIGHOSE MrDrip 9001DB Raindrip Digital Water Timer R673CTSprinkler Warehouse 9001D The Drip Store C001 Toro 53746 Drip Irrigation Timer controllerWater TimerSprinkler TimerAutomatic WateringHose TimerGarden Hose TimerOrbit Hose TimerGilmour Water Timer
Hose Bibb, Faucet, Spigot, Hydrant.
Y Hose Bibb Ball Valve. This 2-outlet ball valve allows for connection of garen hose and drip system from the same hose bibb, faucet, spigot, or hydrant.
Hose Vacuum Breaker Prevents water from flowing back from your drip irrigation system into your household water.
Hose Inline Filter (120 mesh screen)
Pressure Regulator (pre-set) (20 PSI - 30 PSI)
You may also be interested in the following product(s)